View all products of Brembo Racing

Brembo Caliper Dust Boot Ø 40 mm (Dust Seal) | 20487246 / 20.4872.46

  • Part Number: 20.4872.46 / 20487246
  • Alternative Numbers: 105.5955.46, 105.7224.46
  • Piston Diameter: Ø 40 mm
  • Fits: all Brembo calipers with Ø 40 mm pistons
  • Matching Seal Kit: 105.5955.58
  • Matching Piston: 94.4225.07 (Type 3 or 4)
  • Manufacturer: Brembo (genuine part)
📦 Note: Single unit (1 dust boot). One dust boot is needed per piston – for a 4-piston caliper, order 4 pieces.
111
20487246
€13.10
Tax included

Brembo Caliper Dust Boot Ø 40 mm – Part No. 20.4872.46

The genuine Brembo dust boot 20.4872.46 (part number 20487246, also written 20 4872 46) fits all Brembo calipers with Ø 40 mm pistons: fixed calipers with 2, 4, 6 or 8 pistons, whether fitted as original equipment or retrofitted as a Brembo GT or Racing brake system. Alternative numbers: 105.5955.46 / 105.7224.46. It is also known as a caliper dust seal, dust cover or caliper piston boot.

The boot sits between the piston and the caliper body and keeps dust, water, dirt and brake dust away from the piston, the piston bore and the piston seal. If the brake caliper dust seal is cracked, porous or out of place, dirt reaches the piston. This leads to corrosion, scoring and, in the worst case, a stuck piston. The boot is made of heat-resistant, abrasion-resistant rubber and is suitable for road and track use.

Technical Specifications – Brembo Dust Boot Ø 40 mm

Part Number: 20.4872.46
Part Number without dots: 20487246
Alternative Numbers: 105.5955.46, 105.7224.46
Manufacturer: Brembo (genuine part)
Product Type: Caliper dust boot / dust seal for brake pistons (single unit)
Piston Diameter: Ø 40 mm
Fits: All Brembo calipers with Ø 40 mm pistons (2, 4, 6 or 8 pistons; OE, GT and Racing)
Material: Heat-resistant, abrasion-resistant rubber
Matching Seal Kit: Brembo seal kit Ø 40 mm – 105.5955.58 (formerly 105.5955.18)
Matching Caliper Piston: Piston Ø 40 mm to fit Brembo – 94.4225.07 (Type 3 or 4, with dust boot groove)
Scope of Delivery: 1x dust boot
🔧 Replace dust boot and seal together: When you replace the caliper dust boot, always replace the piston seal as well. For Ø 40 mm, the Brembo seal kit 105.5955.58 fits. If the piston also needs replacing, the caliper piston Ø 40 mm (94.4225.07) fits. For seal installation we recommend Brembo SCF Seal Conditioning Fluid. All sizes can be found in our dust seal & dust cover size overview »

Caliper Dust Boot Replacement

The dust boot is replaced together with the piston seal when rebuilding a caliper. The steps in brief:

  • Remove the piston from the caliper, then remove the old dust boot and piston seal.
  • Clean the piston bore, grooves and piston, and check them for scoring or corrosion.
  • Wet the new piston seal (105.5955.58) with Brembo SCF or brake fluid and fit it.
  • Fit the new dust boot (20.4872.46) and insert the piston.
  • Bleed the brake system and check that it works properly.

Work on the brake system should only be carried out by a workshop or suitably qualified persons.

How Many Dust Boots Do I Need?

You need one boot per piston: 4 for a 4-piston caliper, 6 for a 6-piston caliper. Many Brembo calipers have pistons in two sizes (for example 30 mm and 34 mm). Measure each piston and order the matching boot for each size.

Brembo Dust Boots – Vehicle Manufacturers

Brembo calipers are fitted as original equipment by many manufacturers or installed as an upgrade brake system. If your caliper has Ø 40 mm pistons, this dust boot fits – including vehicles from:

  • Abarth
  • Acura
  • Alfa Romeo
  • Alpine
  • Aston Martin
  • Audi
  • Bentley
  • BMW
  • Bugatti
  • BYD
  • Cadillac
  • Chevrolet (Corvette)
  • Chrysler
  • Cupra
  • Dodge
  • Ferrari
  • Ford
  • Genesis
  • Honda
  • Hyundai
  • Infiniti
  • Jaguar
  • Jeep
  • Kia
  • Lamborghini
  • Land Rover
  • Lexus
  • Lotus
  • Maserati
  • McLaren
  • Mercedes-Benz / Mercedes-AMG / Maybach
  • Mitsubishi
  • Nio
  • Nissan
  • Pagani
  • Polestar
  • Porsche
  • Subaru
  • Tesla
  • Toyota (GR)
  • Volkswagen
  • Volvo
  • Xiaomi
  • XPeng
  • Zeekr

What matters is not the vehicle model but the piston diameter in your caliper. Measure the piston or send us your vehicle and caliper type – we are happy to check for you.

FAQ – Brembo Dust Boot Ø 40 mm

Which dust boot fits my Brembo caliper?

The piston diameter decides. Dust boot 20.4872.46 fits all Brembo calipers with Ø 40 mm pistons, regardless of the vehicle manufacturer. All other sizes are listed in the table below.

Is 20.4872.46 the same part as 105.5955.46 or 105.7224.46?

Yes. 20.4872.46 is the current Brembo number; 105.5955.46 and 105.7224.46 are alternative numbers for the same Ø 40 mm dust boot. Diameter and fit are the same.

Which piston seal matches?

For Ø 40 mm, the Brembo seal kit 105.5955.58 (formerly 105.5955.18) fits.

Should I replace the seal when replacing the dust boot?

Yes. Dust boot and piston seal age together and are always replaced together when rebuilding a caliper.

How do I know the dust boot is damaged?

Typical signs are cracks, porous or swollen rubber, a boot that has slipped out of place, and rust or dirt on the piston.

Is this a genuine Brembo part?

Yes. Dust boot 20.4872.46 is a genuine Brembo part.

Brembo Dust Boots, Seal Kits and Pistons – All Sizes

Need a different size? Find all dust boots with the matching seal kit and piston directly in our shop. More details in our dust seal & dust cover size overview and the brake piston size overview:

Piston Ø Dust boot Seal kit Caliper piston
24 mm 20.4872.38 105.5955.50 on request
26 mm 20.4872.39 105.5955.51 on request
28 mm 20.4872.40 105.5955.52 94.4225.01
30 mm 20.4872.41 105.5955.53 94.4225.02
32 mm 20.4872.42 105.5955.54 94.4225.03
34 mm 20.4872.43 105.5955.55 94.4225.04
36 mm 20.4872.44 105.5955.56 94.4225.05
38 mm 20.4872.45 105.5955.57 94.4225.06
40 mm 20.4872.46 (Current product) 105.5955.58 94.4225.07
42 mm 20.4872.47 105.5955.59 94.4225.08
44 mm 20.4872.48 105.5955.60 94.4225.09
46 mm 20.4872.51 105.5955.62 on request

Questions about the right dust boot or seal for your caliper?

Our team at ATG-Racing will be happy to help – use our contact form, give us a call, or send us an email directly.

✍️ Go to contact form 📞 Call us: +49 251 16245580 ✉️ info@racing-professionals.com

Specific References

MPN
20.4872.46

Product Comments

Shopping Cart

Cart is empty.

Account

Account

No account?
Create an Account